Tsunami Pure-7 25 CFM 12VDC Dryer, 21999-1140-MM-12
Protect moisture-sensitive tools, equipment and finished work with the Tsunami Pure-7 25 CFM regenerative dryer. Included two-stage pre-filtration removes liquid water, oil aerosols and fine particulates before molecular sieve desiccant captures water vapor. The result is clean, very dry air for finishing, pneumatic equipment and industrial processes.
This configuration uses 12 VDC control power and Moisture Minder pneumatic drains. It is intended for installations with a compatible DC supply; match the electrical requirements before ordering.
Key Features and Benefits
- Low moisture levels: Dew points down to -80°F and relative humidity down to 0.01% RH, depending on inlet conditions and sizing.
- Two-stage pre-filtration: Water separation followed by oil coalescing filtration helps protect the downstream desiccant.
- Automatic regeneration: Timer-controlled switching alternates tower banks between drying and regeneration.
- Automatic drains: The selected float or pneumatic drain arrangement discharges collected condensate.
- Serviceable design: Replaceable filter elements, towers, valves and piston components support scheduled maintenance.
- One-year warranty: Manufacturer warranty terms and required maintenance apply.
Technical Specifications
| Specification | Details |
|---|---|
| Rated maximum airflow | 25 CFM |
| Compressor sizing reference | 7.5 HP; size by actual airflow and operating conditions |
| Configuration | Wall mounted |
| Connections (NPT) | 1/2" inlet / 1/2" outlet |
| Maximum operating pressure | 175 PSI |
| Maximum inlet air temperature | 150°F |
| Desiccant towers | 2 |
| Control | Solenoid timer valve |
| Regeneration orifice | .024 inch |
| Tower switching interval | Approximately 90 seconds (12 VDC timer) |
Model and Installation Details
| Part number | Power | Drain type | Dimensions (H x W x D) | Approx. weight |
|---|---|---|---|---|
| 21999-1140-MM-12 | 12 VDC | Moisture Minder pneumatic | Contact us for installation dimensions | Contact us for current weight |
Flow capacity depends on inlet pressure, inlet temperature and downstream demand. Allow additional compressor capacity for regeneration air. A storage tank supports brief demand peaks but does not increase the dryer’s continuous CFM rating. Call 877.247.2381 for application sizing.
How the Dryer Works
Incoming air first passes through the water separator and oil coalescing pre-filter. Desiccant in the active tower bank captures water vapor, while a portion of dry air purges moisture from the regenerating bank. The solenoid timer valve switches the banks automatically. Regeneration uses compressed air, so include that demand when sizing your compressor.
Maintenance Parts and Replacement Elements
Use the parts below for your selected model. Parts are sold separately. This dryer has 2 desiccant towers; match service quantities and electrical components to your equipment.
| Part number | Service item |
|---|---|
| 21999-0227 | Water separator service kit |
| 21999-0202 | Oil coalescing filter service kit |
| 21999-0825 | Oil coalescing replacement elements, five-pack |
| 21999-0349 | Replacement desiccant tower, purple; sold individually |
| 21999-0349-BK | Replacement desiccant tower, black; sold individually |
| 21999-0707 | Piston replacement kit |
| 21999-1149 | Piston O-ring service kit for 12 pistons |
| 21999-0650-24 | Tower mounting stud / regeneration valve, .024-inch orifice |
| 21999-0700 | Replacement exhaust mufflers, two-pack |
| 21999-0795 | Moisture Minder pneumatic filter drain; requires pilot signal |
| 21999-0797-12 + 21999-0504 | 12 VDC air valve and timer/coil assembly; sold separately |
Shop the Tsunami Parts collection for additional repair components and maintenance supplies.
Maintenance Schedule
- Every six months: Replace the oil coalescing element and inspect/lubricate the pistons and piston bores as directed in the dryer manual.
- Three-year service: Replace desiccant towers and pistons according to the model-specific instructions.
- Inspect automatic drains and follow the service requirements for your operating conditions. Isolate power and release all system pressure before service.
Ideal Applications
Automotive and woodworking finishing, pneumatic tools and controls, manufacturing equipment and other moisture-sensitive compressed air applications. Select the dryer and filtration arrangement to meet the air-quality requirements of your process.
Frequently Asked Questions
Is a compressor included?
No. This is an air-treatment system supplied by an external compressor. The compressor must provide the required operating pressure and airflow, including regeneration demand.
What is the difference between float and pneumatic drains?
Float drains discharge condensate automatically as liquid collects. Moisture Minder pneumatic drains use a pilot signal from the dryer control to discharge condensate. Select the drain arrangement shown for the exact part number.
Which coalescing replacement should I order?
Use 21999-0202 for the compatible service kit or 21999-0825 for a five-pack of replacement elements. Match the complete part number to your pre-filter.
Can you help me size this dryer?
Yes. Call Compressed Air Advisors Online at 877.247.2381 with your compressor output, operating pressure, inlet temperature and application requirements.
Installation and Maintenance Manual
Download the Pure Series installation and maintenance manual. Match the instructions to your model and control voltage.